How to configure A800 and A400e in one server

Hi,
You only need to run the command:
genzaptelconf -sdvM
ztcfg -vvvv
Please check the channels in /etc/asterisk/zapata-channels.conf

After the genzaptelconf -sdvM it still not work (i had try on amportal off/on condition), below is the output :

[root@ltrsc asterisk]# genzaptelconf -sdvM
/usr/sbin/genzaptelconf: line 1124: /etc/init.d/asterisk: No such file or directory
Unloading zaptel modules:

Temporarily moving zaptel.conf aside to work around broken modprobe.conf
Test Loading modules:
- wct4xxp
- opvxd115
- wcte12xp
- wcte11xp
- wct1xxp
- wanpipe
- tor2
- torisa
- qozap
- vzaphfc
- zaphfc
- ztgsm
- wctdm24xxp
- wctdm
ok opvxa1200
- wcfxo
- pciradio
- wcusb
- xpp_usb
Updating modules list in zaptel init config /etc/sysconfig/zaptel.
Generating '/etc/zaptel.conf and /etc/asterisk/zapata-channels.conf'
Note: generated /etc/asterisk/zapata-channels.conf not included in zapata.conf
To fix: echo '#include zapata-channels.conf' >>/etc/asterisk/zapata.conf
Reconfiguring identified channels

Zaptel Version: 1.4.12.1
Echo Canceller: OCTVQE
Configuration
======================


Channel map:

Channel 01: FXS Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Slaves: 03)
Channel 04: FXS Kewlstart (Default) (Slaves: 04)
Channel 05: FXS Kewlstart (Default) (Slaves: 05)
Channel 06: FXS Kewlstart (Default) (Slaves: 06)
Channel 07: FXS Kewlstart (Default) (Slaves: 07)
Channel 08: FXS Kewlstart (Default) (Slaves: 08)

8 channels to configure.

Checking channels configured in Asterisk:
Unable to connect to remote asterisk (does /var/run/asterisk/asterisk.ctl exist?)
[root@ltrsc asterisk]#

Im sure the card is plug in, below is the lspci -vvvv result :

02:00.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device b100:0001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <;PERR-
Latency: 32 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 169
Region 0: I/O ports at ec00

06:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface
Subsystem: Unknown device 9500:0003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr+ DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <;PERR-
Latency: 32 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 50
Region 0: I/O ports at d800

i] Last edited by cylim at 2010-9-29 13:36 [/i

Hi,
Please run the command:
service zaptel stop
modprobe zaptel
modprobe opvxa1200 opermode=your country
modprobe wctdm opermode=your country
cd /usr/src/zaptel-xxxx/kernel/xpps/utils
./genzaptelconf -sdvM
ztcfg -vvvv

When I type: modprobe opvxa1200 opermode=MY

Result :
[root@ltrsc utils]# modprobe opvxa1200 opermode=MY
FATAL: Error inserting opvxa1200 (/lib/modules/2.6.18-164.el5PAE/misc/opvxa1200.ko): No such device

If I do without opermode, the command runs smooth, but the A400E still not working.

Below is the ouput :

[root@ltrsc utils]# service zaptel stop
Unloading zaptel hardware drivers:.
[root@ltrsc utils]# modprobe zaptel
[root@ltrsc utils]# modprobe opvxa1200
[root@ltrsc utils]# modprobe wctdm
[root@ltrsc utils]# cd /usr/src/zaptel-1.4.12.1/kernel/xpp/utils/
[root@ltrsc utils]# ./genzaptelconf -sdvM
./genzaptelconf: line 1124: /etc/init.d/asterisk: No such file or directory
Unloading zaptel modules:

Temporarily moving zaptel.conf aside to work around broken modprobe.conf
Test Loading modules:
- wct4xxp
- opvxd115
- wcte12xp
- wcte11xp
- wct1xxp
- wanpipe
- tor2
- torisa
- qozap
- vzaphfc
- zaphfc
- ztgsm
- wctdm24xxp
- wctdm
ok opvxa1200
- wcfxo
- pciradio
- wcusb
- xpp_usb
Updating modules list in zaptel init config /etc/sysconfig/zaptel.
Generating '/etc/zaptel.conf and /etc/asterisk/zapata-channels.conf'
Note: generated /etc/asterisk/zapata-channels.conf not included in zapata.conf
To fix: echo '#include zapata-channels.conf' >>/etc/asterisk/zapata.conf
Reconfiguring identified channels

Zaptel Version: 1.4.12.1
Echo Canceller: OCTVQE
Configuration
======================


Channel map:

Channel 01: FXS Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Slaves: 03)
Channel 04: FXS Kewlstart (Default) (Slaves: 04)
Channel 05: FXS Kewlstart (Default) (Slaves: 05)
Channel 06: FXS Kewlstart (Default) (Slaves: 06)
Channel 07: FXS Kewlstart (Default) (Slaves: 07)
Channel 08: FXS Kewlstart (Default) (Slaves: 08)

8 channels to configure.

Checking channels configured in Asterisk:
No such command 'zap show channels' (type 'help zap show' for other possible commands)

[root@ltrsc utils]# ztcfg -vvvvv

Zaptel Version: 1.4.12.1
Echo Canceller: OCTVQE
Configuration
======================


Channel map:

Channel 01: FXS Kewlstart (Default) (Slaves: 01)
Channel 02: FXS Kewlstart (Default) (Slaves: 02)
Channel 03: FXS Kewlstart (Default) (Slaves: 03)
Channel 04: FXS Kewlstart (Default) (Slaves: 04)
Channel 05: FXS Kewlstart (Default) (Slaves: 05)
Channel 06: FXS Kewlstart (Default) (Slaves: 06)
Channel 07: FXS Kewlstart (Default) (Slaves: 07)
Channel 08: FXS Kewlstart (Default) (Slaves: 08)

8 channels to configure.

Hi,
Please send SSH to my email. This email address is being protected from spambots. You need JavaScript enabled to view it. I'll check for you.